Batch File Commands Return Error Code
Logged To every complex question there is a simple answer and it is wrong…- H.L. Join them; it only takes a minute: Sign up Get error code from within a batch file up vote 26 down vote favorite 5 I have a batch file that runs Consider using !errorlevel! American English: are [É™] and [ĘŚ] different phonemes? this contact form
SomeFile.exe IF %ERRORLEVEL% EQU 9009 ( ECHO error - SomeFile.exe not found in your PATH ) It’s hard to know this stuff upfront – I generally just use trial and error asked 4 years ago viewed 52019 times active 9 months ago Get the weekly newsletter! Convince people not to share their password with trusted others Is 8:00 AM an unreasonable time to meet with my graduate students and post-doc? There is not enough memory or disk space, or you entered an invalid drive name or invalid syntax on the command line. 5 = Disk write error occurred.
Batch File Commands Wait
Errorlevel checking is done as a greater-or-equal check, so any non-0 exit value will trigger the jump. If executed from outside a batch script, it will quit CMD.EXE exitCode specifies a numeric number. devcomApprenticeThanked: 37 Re: How to return success/failure from a batch file? « Reply #8 on: September 10, 2008, 01:12:38 AM » you can use:Code: [Select]&& if success
|| if failexample:Code: [Select]set Logged To every complex question there is a simple answer and it is wrong…- H.L.
Happened when checking %ERRORLEVEL% in a cmd file. GTIN validation Which requires more energy: walking 1 km or cycling 1 km at the same speed? I've been using the 0 and 1 return codes with copy and they work fine. –Bill Ruppert Dec 15 '15 at 14:34 add a comment| Your Answer draft saved draft Batch File Xcopy Commands It seems like the MS-DOS internal commands do not return an error code.
Instead, you can use "if %ERRORLEVEL% EQU 0 (..)". –Curtis Yallop Jul 29 '14 at 16:06 Found cases where %ERRORLEVEL% is 0 even though an error occurred. Batch File Copy Commands Mencken fireballsApprentice Code:TerminalThanked: 3 Re: How to return success/failure from a batch file? « Reply #7 on: September 09, 2008, 06:57:18 PM » Quote from: Sidewinder on September 09, 2008, 06:51:56 It is in form of boolean values, with 0 for success and 1 for failure. A very helpful feature is the built-in DOS commands like ECHO, IF, and SET will preserve the existing value of %ERRORLEVEL%.
If not, why? Batch File Loop Commands Subscribed! Adopt A Jet/Book Limit involving exponentials and arctangent without L'Hôpital Were slings used for throwing hand grenades? I got the following error: 0 was unexpected this time. –Misha Moroshko Oct 1 '10 at 5:13 2 @Misha: You may have tried it with the percent signs the way
Batch File Copy Commands
windows batch-file dos command-prompt share|improve this question asked Feb 16 '13 at 1:15 Martin 11.4k38135215 To return anything, it has to finish... –vonbrand Feb 16 '13 at 1:43 add How to make different social classes look quite different? This is rare for scripts intended for interactive use, but, it can be super helpful when writing scripts you support but you don’t have access to the target systems. @ECHO OFF navigate here There is not enough memory or disk space, or you entered an invalid drive name or invalid syntax on the command line. 5 Disk write error occurred.
Old Forum Search | Forum Rules Copyright © 2013 Computer Hope All rights reserved. Batch File Date Commands Finding a file starting with '-' dash American English: are [É™] and [ĘŚ] different phonemes? By default, the command processor will continue executing when an error is raised.
This type of compare ("%errorlevel%=="0") becomes dubious at best.B.bat can use the exit statement to pass a return code (errorlevel) back to a.bat.QuoteQuits the CMD.EXE program (command interpreter) or the current
I was thinking more along the line where b.bat would abort early based on some condition:b.batCode: [Select]if not exist c:\file.ext exit 7
if not defined userprofile exit 9
a.bat I'm a software developer loving life in Charlotte, NC, an (ISC)2 CSSLP and an avid fan of Crossfit. SomeCommand.exe || EXIT /B 1 A simliar technique uses the implicit GOTO label called :EOF (End-Of-File). Batch File Ftp Commands Error occurred while processing: .exe1How to perform “find” command with another embedded command in another directory?4How to prevent a bat file exiting early?3replace a character in the string using DOS commands1Not
share|improve this answer edited Feb 5 at 1:18 answered Jun 28 '11 at 0:24 paxdiablo 488k1179691416 Thanks. see more linked questionsâ€¦ Related 641How to pass command line parameters to a batch file?294How can you find and replace text in a file using the Windows command-line environment?349How to get SomeCommand.exe || GOTO :EOF Tips and Tricks for Return Codes I recommend sticking to zero for success and return codes that are positive values for DOS batch files. http://sovidi.com/batch-file/batch-file-return-error-code.php The only internal cmd.exe command capable to do so is EXIT /B exitcode that use a nonstandard, undocumented method to set a 32-bits signed value.