Bios Error 01 Reading Hard Disk
I will try one more time and then maybe I will give it to the service! It gets up to Amdide.sys, hangs for a while and shuts down, only to reboot and start the whole process again. After such a repair it is very possible that one of more files were corrupted and are now unusable. If your computer is operating but has a problem such as "cannot read sectors" or in general shows a "retry , abort ,ignore" error while reading the drive, it is an have a peek at these guys
There are two methods in use. On some computers you can enter the BIOS from a DOS prompt. a) older computers On these computers you have to go into the CMOS/BIOS during boot and change the setting by selecting a number from 1 to 48, by selecting a TYPE Several functions may not work.
Could this indicate an issue with the BIOS that's maybe causing the firmware not to see the hard drive? A normal hard drive has a smooth whine so its should be easy to identify the bad drive by just listening. 4. On 2 drive systems, the first drive should be setup as Master and the second as Slave and the secondary channel is ignored. I hope you have a great day! ---------------------------------------------------------------------------------------------------Please click the white star under my name to give me Kudos as a way to say "Thanks!"Click the "Accept as Solution" button if
copy a:\command.com c:\command.com
I suspect there may be a registry error, but wouldn't know where to start looking for one. I am able to access the BIOS, and the diagnostic log shows error codes 0303 and 0305. I was afraid it'd come to a fresh install, however I'd much prefer not to loose all my data, as I don't have a proper backup (stupid, I know). The BIOS information is stored in the CMOS hardware section of the motherboard and the contents are maintained by applying constant electrical current using a CMOS battery .
Another way is to use a utility program like Norton Utilities to perform the surface scan. However, when I booted Ubuntu from a usb stick, I was able to access the hard drive and the files on the computer. Post back if you want to discuss motherboard replacement options. 0 0 That_TechGuy Honor Student Posts: 2 Member Since: 04-13-2012 Message 4 of 16 (50,764 Views) Report Inappropriate Content Re: Hard Therefore, the hard drive is working.
This causes the computer to not see the secondary hard drives immediately after the installation of this device using IRQ 15. Back to top BC AdBot (Login to Remove) BleepingComputer.com Register to remove ads #2 Serpius Serpius Banned 121 posts OFFLINE Gender:Male Local time:08:42 AM Posted 06 April 2015 - If there are lights, then it could be one of the I/O cards. You can also copy the command.com file from the floppy to the hard drive by typing...
Very critical also is the LBA setting which can cause the drive to operate but not be able to see all the data. More about the author The size that Fdisk reports is the full size of the hard disk minus 64 GB. The other "good" drive should have at least started to boot. The hard drive has failed electronically This will be indicated by an error message during the computer boot cycle.
If the drive is not spinning, turn off the power and try using a different power plug (maybe the one that the CD-ROM is connected). I ran all the diagnostics and the memory checked 100% fine, but the computer says there is no hard drive installed. Gateway 2000 - F1 Hewlett Packard - F1 Back to Support Doc's [ Home ] [ About Us ] [ Contact Us ] [ Services ] [ Support check my blog I will try to answer any questions to the best of my abilities.
After entering these parameters you will normally save them before exiting the BIOS program and then reboot the computer. Using the site is easy and fun. Windows).
Louis Forum Rules Report Topics For Staff Action BC Forums, List Preparation Guide Before Posting Malware Issues in MRL Forum Am I Infected Forum Back to top #8 Tijmen Tijmen Topic
If windows 95 sees a conflict with these drivers it will switch itself into the DOS compatibility mode. It is reasonably priced and WILL repair hard drive problems WITHOUT destroying your data. Also, there's a very small (maybe 1 inch long) cable on this laptop that connects the hard drive to the motherboard. 1 end connects via normal SATA ports but the other Note: A drive must also have the BOOT partition activated before it can boot properly.
I took the hard drive out and checked the connectors for corrosion or burns and everything looked clean. I have a lot of very important personal information and family photos on the G42 so if anyone knows a way to fix this problem outside of a new hard drive Some of these cables are also keyed by having a small tab in the center of the connector's edge. news With your hand touch that side and try to feel the spinning of the hard drive platter.
Although that seemed to work, /bootfix resulted in another I/O error. It is impossible to tell which files will be affected in advance but if you write down the bad file names shown during the scan disk operation you can try to I removed re-seated the drive several times but it didn't fix anything. Back to top #6 Tijmen Tijmen Topic Starter Members 7 posts OFFLINE Local time:02:42 PM Posted 06 April 2015 - 09:18 AM So, apparently I can't use the usb-mounted ubuntu
edit: corrected laptop model Tijmen, I am suspecting that you may have a bad Master Boot Record on that hard drive. Once in BIOS you can change the hard drive type to AUTO and after shutting off the computer and reconnecting the hard drive, try again to see if it now works. There is some type of electrical connection problem Make sure the cable connections are correct. Click Repair your computer.
IRQ conflicts and bad jumper settings could cause this problem as well. Search Product Browse for Products Home· Forums· About Us· Awards· Contact Us· Upgrade your BIOS BIOS UPDATES Click to scan for Bios Updates BIOS PostCodes Acer ALR AMIT/AMI Arche Legacy AST Several ways can be used to enter the BIOS/CMOS: The video monitor will usually say on the bottom of the screen just as the computer is turned on, which key to Windows 95, 98, ME, XP, NT4, 2000, Errors, Applications, Search products , Search FAQs.Shop Companies, Products, How to Troubleshoot Hard Disk Drive Problems | Tech Info Home | Troubleshooting |
Thank you! Register · Log In HP Support Forum Home > Notebooks > Hardware > Hard drive not found (3F0) error HP Support Forums Join in the conversation. Happy computing .