Home > Bit Error > Bit Error Rate To Packet Error Rate Conversion

Bit Error Rate To Packet Error Rate Conversion

Contents

How to setup register retention mode timer on, on the nRF24LE1? There is no test mode/direct mode that allows you to measure the BER (bit error rate) directly, but there are some ways to get a good indication of the sensitivity limit How to measure Bit/Packet Error Rate (BER/PER) on the nRF24L01? Where can I find example code for the device? news

Generated Sun, 02 Oct 2016 06:15:05 GMT by s_hv972 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.9/ Connection A worst-case scenario is a completely random channel, where noise totally dominates over the useful signal. Must the ADC input pins on the nRF24E1 and nRF9E5 be connected to a defined level when not in use? Measuring the bit error ratio helps people choose the appropriate forward error correction codes.

Bit Error Rate Calculation

Abdul Jabbar jabbar at gmail.com Mon Oct 2 03:59:56 PDT 2006 Previous message: [ns] FW: how do i transfrom "Bit Error Rate" to "Packet Error Rate"? How to setup deep sleep on the nRF24LE1? A more general way of measuring the number of bit errors is the Levenshtein distance. Why does Keil crash at random times when using the nRF51 kits after upgrading to J-Link 4.56?

Generated Sun, 02 Oct 2016 06:15:05 GMT by s_hv972 (squid/3.5.20) Why should I use the recommended layout for the antenna matching network? Why do I get “Error: Flash download failed – Cortex-M0” when downloading a project from Keil? Bit Error Rate Pdf I am not able to debug or program my nRF device from Keil, what might be the problem?

I want to use an antenna with an impedance different from 50 ohm. Bit Error Rate Test nRF51422 What can I do to get rid of errors about --asm and --interleave when compiling nRF51-projects? How to configure the nRF24L01/nRF24L01+ to RX mode? Do you have a printed 868/915MHz loop antenna layout available for the nRF905/nRF9E5 device?

Development tools Layout files Can I use a WLAN or Bluetooth antenna together with the Nordic 2.4 GHz nRF devices? Bit Error Rate Matlab How to set wakeup from powerdown mode with nRF9E5? By using this site, you agree to the Terms of Use and Privacy Policy. How can I match this antenna to the nRF device antenna port?

Bit Error Rate Test

Do I need Keil CA51 or PK51 to develop with the nRF24LE1 and nRF24LU1P? Which power down mode should I use with the nRF24LE1? Bit Error Rate Calculation How should I connect the quarter wavelength printed monopole antenna, documented in your white paper, to the nRF device? Bit Error Rate Example How to setup register retention mode on the nRF24LE1?

Do I need Keil CA51 or PK51 to develop with the nRF24LE1 and nRF24LU1P? http://sovidi.com/bit-error/bit-error-rate-data-rate.php Why does Keil crash at random times when using the nRF51 kits after upgrading to J-Link 4.56? Do I need Keil CA51 or PK51 to develop with the nRF24LE1 and nRF24LU1P? How to setup register retention mode on the nRF24LE1? Bit Error Rate Vs Snr

Can I use a WLAN or Bluetooth antenna together with the Nordic 2.4 GHz nRF devices? How useful is Carrier Detect (CD) on the nRF24L01? Do I need to re-qualify my design because of the new information in revision 2.0 of the nRF24L01 Product Specification? http://sovidi.com/bit-error/bit-error-rate-packet-loss.php Do you have a printed 868/915MHz loop antenna layout available for the nRF905/nRF9E5 device?

I want to make a new product with the nRF401, nRF403 or nRF903 I want to use a 4 layer pcb, I intend to run signal/gnd/pwr/signal, what is the best to Ber Repair Is the source code for the PC application for the evaluation kits available? Do I need to tune the antenna in my design to acheive 50 Ohm impedance?

How do I configure the nRF24Z1 from MCU, without using an EEPROM?

Do I need an MCU or EEPROM together with the nRF24Z1? Generated Sun, 02 Oct 2016 06:15:05 GMT by s_hv972 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.6/ Connection How should I connect the quarter wavelength printed monopole antenna, documented in your white paper, to the nRF device? Ber Meaning QRSS (quasi random signal source) – A pseudorandom binary sequencer which generates every combination of a 20-bit word, repeats every 1,048,575 words, and suppresses consecutive zeros to no more than 14.

Should we connect the die attach pad on the QFN package? How can I match this antenna to the nRF device antenna port? Many FEC coders also continuously measure the current BER. http://sovidi.com/bit-error/bit-error-rate-and-data-rate-relation.php nRF24E1 When will Nordic Semiconductor obsolete/End-of-Life device X?

I want to make a new product with the nRF401, nRF403 or nRF903 I want to use an antenna with an impedance different from 50 ohm. Why should I use the recommended layout for the antenna matching network? I have a question that is not answered here, where can I direct my question? Why does my program not run and the debugger shows the code being only 0xFFs?

Why should I use the recommended layout for the antenna matching network? nRF24LU1P When will Nordic Semiconductor obsolete/End-of-Life device X? Packet Error Rate (PER) Go To Silicon Labs Community Forum Welcome and Announcements Silicon Labs Knowledge Base Microcontrollers 8-bit MCU 32-bit MCU Wireless Bluetooth / Wi-Fi Mesh Proprietary Other Products Category How to configure the nRF24L01/nRF24L01+ to TX mode?

How to setup deep sleep on the nRF24LE1?