Balboa Hl Error Code
Lol Share this post Link to post Share on other sites christiffa25 0 Junior Member Members 0 38 posts Posted June 1, 2012 · Report post Ok hopefully final *update* HLoH = Hi Limit Over Heat. Email Address: Password: You will be prompted to enter your password on the next page Create an account Forgot Password? If the "SF" Error Message is not cleared from the topside panel display, contact your Dealer or Service Organization. Check This Out
The tub temp actually dropped 5 degrees today. Closed Slice Valve.7. Chances are it is a bad pump or blower. Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F.SEoP = Sensor open or disconnected.
Balboa Sns Error Code
For more information regarding Balboa tech support click here Gecko Spa Side Error Codes FLO : Pressure switch failure, switch open FLC : Pressure switch failure, switch closed Prr : Temp Press "Mode" Button to Clear Message. Plug in a test transformer and test panel, and return power to the hot tub. Do not use spa when temperature is flashing or the OH message is displayed.
- Heated for 2 hours then OH error again..
- Share this post Link to post Share on other sites christiffa25 0 Junior Member Members 0 38 posts Posted May 25, 2012 · Report post It's been suggested to me
- Check the slice valves and verify that they are open.
- Seem to be getting conflicting info regarding temp sensor readings??
- Back to Top DETAILED PRIMING INSTRUCTIONS In Priming Mode, Nothing turns on Automatically*.*Note: On the VS/GS Model, the Circ Pump will be on, and on some EL/GL Models, a continuous filtration
- Read our FAQ!
- It heated for around 10 hours nearly getting up to full temp before cutting out and displaying OH again!
The Spa or Hot Tub Panel Displays: SL This indicates the system is in sleep mode and can be changed by pressing the up temp. Rare system error. Check for blown fuses, burn marks or signs of tampering in the box. Balboa High Limit Switch Location All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 180 Days, but some Spa Brands or Models may be Different.
The sensor that is plugged into the sensor "A" jack is not working 'Sb' Spa is shut down. Why does the panel display "SN3"? All Reminder Messages can be Disabled through the Topside Panel Users Menu.Note: The Balboa Default is to have this Message Disabled. Heater is shut down, but other spa functions run normally.dr = Inadequate water detected in heater.dry = Inadequate water detected in heater. (Displays on third occurrence of "dr" message).
If Not, Continue to Next Step.Spas with Pump Suction Blockage Switch:1. Balboa Hot Tub Error Codes Press the "light" button once only. It's the older board where you have a hi-limit sensor going into the spa shell and a temp sensor in going into the heater along with a pressure switch going into Admitably and regrettably, my memory is NOT the greatest!
Arctic Spa Hl Error Code
Then press Temp once to exit Priming Mode. DO NOT remove the protective covers from any electrical enclosure, or attempt to service any related electrical device, unless you are a qualified electrician or service professional. Balboa Sns Error Code There was no corrosion. Hl Error Code Hot Tub Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F.
One sensor has detected 118° F at heater. his comment is here OH = Over heat. If alternating with temp, may be temporary condition. Back to Top SnA, SA, or SENSOR A SERVICE REQD Message "Sensor A" (SnA or SA) is Not Operating Correctly.The Sensor Connected to the "Sens.A" Connector on the System Board may Balboa High Limit Sensor
The Spa or Hot Tub Panel Displays: Cd, CLd This indicates that a sensor detects a possible freeze condition. Make sure that they are open. Does it matter they are slightly different readings? http://sovidi.com/error-code/balboa-error-code-oh.php Check for proper spa water level and ensure pump is primed.
th3/39 = On startup indicates water temperature less than 39° F. Balboa Spa Control Manual The Sensors are Verified Out of Sync with Each Other, or Not Indicating Close to the Same Temperature at Both Sensors. A few more hours and I should see clearly Logged Water Boy Full Member Posts: 627 Re: HL reading « Reply #10 on: January 03, 2009, 07:06:12 PM » Bosco,I agree
My tub reverts to a default temp of 95 on power up.
Where can I find your product manuals? You had a bad board. The Water Temperature is Sampled Only during Programmed Filter Cycles. Balboa Hot Tub Codes Sl You can often determine the make of the control system by looking inside the spa's equipment area.
You can leave a response, or trackback from your own site. My tub went the other way, the temperature dropped and the HL reading came on. However he had pretty much replaced the board by then so didn't want to swap all back just to test. navigate here Adding cool water may be necessary.
Press any "Cool", "Warm", or "Temp" Button to Exit Priming Mode.3. The lid was open for an hour or so and I went to close the lid and have the reading HL. Make sure the pressure switch wire is connected to the proper circuit board connector. The low speed pump or circ pump will operate continuously until the temperature rises above 45° F.
FL1 = Water flow problem, inhibited or pressure switch malfunction. Press Any Button to Reset and Clear the Error Message.3. Heater disabled but the spa is operational. COOL = Spa water is more than 20° F cooler than the temperature set point.FLO* = Flow Switch (heater is deactivated.
I have had no interruption in my hydro though?? ToE = Time out error. If the flow rate still seems less than normal with all jets and valves open, you may consider inspecting for broken valves (closed when they appear to be open), clogged impeller In my opinion on mine I believe it was the board.
ICE = Freeze condition. 55°F detected. Press "Mode" Button to Clear Message. Protect from FreezingCover Cleaning and AdviceAcrylic Surface Care and MaintenancePurchase a "Made for Michigan" Spa Cover>Spa Cover MeasuringPurchase a Spa Cover Lift AssistantWhirlpool & Air Bath TubsSystem Cleaning-Home remedyAcrylic Surface Care Followed by OH flashing.
If an ozonator is present, disconnect it. One sensor has detected 118º F. All rights reserved. To read the Current Water Temperature, either Change to Standard Heating Mode or turn On the Heating Related Pump, and wait at least 2 Minutes.