Home > Error Code > Bind Failed With Error Code 10049

Bind Failed With Error Code 10049

Contents

This normally results from an attempt to bind to an address that is not valid for the local machine. Note that this error is returned by the operating system, so the error number may change in future releases of Windows. For reference i had attached the sdk sample program that i downloaded as well. Related 1How bind socket to device in windows?2c windows connect() fails. this content

Privacy Legal Site Map Contact Webmaster Helping the World Communicate! Cannot translate a name. Not the answer you're looking for? A connect request was made on an already-connected socket.

Make_listen_bind Bind Failed Socket 1 Code 10049

WSA_QOS_ADMISSION_FAILURE 11010 QoS admission error. This is the content shown in my command prompt when i tried to execute the program ... This is as if the address is invalid.

When bind is called with a wildcard address (involving ADDR_ANY), a WSAEADDRINUSE error could be delayed until the specific address is committed. It means the connection is closed. A service provider returned a bogus procedure table to Ws2_32.dll. Connection Failure Error Code 10049 Lineage 2 error 10049-1bind() fails with windows socket error 100382Receiving Multicast Messages on a Multihomed Windows PC10Bind error while recreating socket1bind () to an IPv6 address in windows 7 is Failing with Error

Get Started with C or C++ C Tutorial C++ Tutorial Get the C++ Book All Tutorials Advanced Search Forum General Programming Boards Networking/Device Communication Winsock error 10049 Getting started with C Connection Failure Error Code 10049 Note that this error is returned by the operating system, so the error number may change in future releases of Windows. WSAEDQUOT 10069 Disk quota exceeded. I would suggest to memset zero the below arrays,structures: struct sockaddr_in6 server, client; SOCKET sock; char buffer[BUFFERSIZE]; LPTSTR recvBuff[1024]; share|improve this answer edited Sep 5 at 10:44 EJP 196k17140247 answered Jan

WSAECONNREFUSED 10061 Connection refused. Socket Error Codes The requested address is not valid in its context. If there is more than one Winsock DLL on your system, be sure the first one in the path is appropriate for the network subsystem currently loaded. and is listening on that ip with port 12345 (netstat -na) =>trying to connect via "" works , but localhost fails...

Connection Failure Error Code 10049

An invalid FILTERSPEC was found in the QoS provider-specific buffer. WSAGetLastError=[10049] Reply With Quote December 6th, 2011,03:37 PM #5 MikeAThon View Profile View Forum Posts Elite Member Power Poster Join Date Nov 2002 Location California Posts 4,556 Re: Winsock error 10049 Make_listen_bind Bind Failed Socket 1 Code 10049 Strange - is this something to do with specific ports?I received a response in the newsgroups - something about Vista SP1's anti-malware logic. Error Code 10049 Origin WSAEMSGSIZE 10040 Message too long.

And when running in the client mode, you must pass in the IPv6 loopback address of 0:0:0:0:0:0:0:1 You can find more information on this by reading the "help" on the command http://sovidi.com/error-code/bind-error-code-22.php When a particular Windows Sockets function indicates an error has occurred, this function should be called immediately to retrieve the extended error code for the failing function call. See WSAENETUNREACH. What is the address you are trying to connect to? Error Code 10049 Bluetooth

In it, you'll get: The week's top questions and answers Important community announcements Questions that need answers see an example newsletter By subscribing, you agree to the privacy policy and terms Can filling up a 75 gallon water heater tank without opening a faucet cause damage? I seem to be getting the exact same problem! have a peek at these guys An example is using a broadcast address for sendto without broadcast permission being set using setsockopt(SO_BROADCAST).

it says "attempt to create a socket with an address not on this machine". What Is A Socket Error How does Gandalf get informed of Bilbo's 111st birthday party? A request to send or receive data was disallowed because the socket had already been shut down in that direction with a previous shutdown call.

To check which ports are bound at any point in time, you can run the following command from the DOS prompt: netstat -ano -p UDP Microsoft Windows allows you to define

The reason in my case was not the same as in the initial poster's code, but i guess other will have made the very same mistake as me: I generated the Is that a good one to learn? –lowerkey May 18 '10 at 6:18 I added the lines servIP = argv[1]; and echoString = argv[2] right after the first if-block. WSA_QOS_TRAFFIC_CTRL_ERROR 11014 QoS traffic control error. Wsagetlasterror 0 WSAEREMOTE 10071 Item is remote.

This can also result from connect, sendto, WSAConnect, WSAJoinLeaf, or WSASendTo when the remote address or port is not valid for a remote machine (for example, address or port 0). Not the answer you're looking for? No connection could be made because the target computer actively refused it. check my blog A blocking operation was interrupted by a call to WSACancelBlockingCall.

Client Code: // thanks to cs.baylor.edu/~donahoo/practical/CSockets/code/TCPEchoClientWS.c #include #include #include #define RCVBUFSIZE 32 // size of receive buffer void DieWithError(char *errorMessage); int main(int argc, char* argv[]) { int sock; An unknown or conflicting QoS style was encountered. WSAECANCELLED 10103 Call has been canceled. An incorrect number of QoS FILTERSPECs were specified in the FLOWDESCRIPTOR.

A request to send or receive data was disallowed because the socket is not connected and (when sending on a datagram socket using sendto) no address was supplied. The WSAGetLastError function returns the last error that occurred for the calling thread.