Home > Error Codes > Balboa Pack Error Codes

Balboa Pack Error Codes

Contents

The Heater will Only operate and Heat up to Set Temperature during the Filter Cycles. FL2 = Pressure switch problem. If water is flowing from the circ pump outlet, proceed to test all the other pumps.If the Circ Pump is primed, or if you Do Not have a Circ Pump, then:- Back to Top - - F, - - C, or - - Message The Actual Water Temperature is "Unknown" (- -).Priming Mode has been Exited and the Pump has Not yet have a peek here

If there is Now a Message Other than a "rtC" or "RTC FAILURE" Real Time Clock Error Message, that Message will Now have to be Diagnosed. The Water Temperature is Always maintained within 1°F (.5°C) of Set Temperature. Advanced Search Forum > Swimming Pool Care > Spas and Hot Tubs > SN code on Balboa control Welcome to Trouble Free Pool We would like to welcome you to TFP, This is normal and is not an indication of an error.

Balboa Spa Error Codes

If you have a Circ Pump, do this first (EL version):- Push the Jets 1 button once. Email Address: Password: You will be prompted to enter your password on the next page Create an account Forgot Password? System will restart when temp.

SESH = Sensor short, nonfunctional. ICE2 = Freeze protection. ILOC = Interlock failure - possible pump or ozone spike. (---) =Unknown water temperature. (Displays when first powered up after refill). Balboa Hot Tub Error Codes SnS = Sensors out of balance.

Contact your Dealer or Service Organization. Balboa Vs501z Error Codes In this condition, an attempt is made to trip the GFCI, which would shut off all power to the spa. If you do not see water flowing from the circ pump outlet, IMMEDIATELY turn off power to the spa (as an attempt at heating will occur within a minute of the Heater is deactivated.

All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 365 Days, but some Spa Brands or Models may be Different. Balboa Fault Codes HOT = Circuit Board temperature has exceeded acceptable limit. If there is No Error Message, Select "No Error Message" Below. FL = Flow.

  1. Low speed pump and heater will activate until spa reaches 65°F.
  2. HFL = Substantial difference between temperature sensors detected.
  3. Press Any Button to Reset and Clear the Error Message.3.

Balboa Vs501z Error Codes

ehowathomechannel 233,067 views 2:42 Loading more suggestions... Pressure switch is not working. Balboa Spa Error Codes All Automatic Functions Remain OFF during this time. Balboa Vs500 Error Codes PSoL = Pressure switch open with low pump.

I should have checked the fuse first. navigate here Water temperature has reached 118ºF. OHH = Overheat. Could indicate a flow problem. Balboa Spa Control Error Codes

Test and Adjust pH Level per Manufacturers Instructions. Low Water Level.2. I have you guys bookmarked now for all my hot tub needs and will be referring others to ur site because of ur prompt service and very reasonable prices." - Sarah http://sovidi.com/error-codes/beep-codes-and-error-codes.php As a responsible adult, always check the topside control panel display for errors and verify safe water temperature before using a spa, and before allowing children to use a spa.

After about 45 Seconds, Check for Error Messages on the Topside Panel Display. Balboa Trouble Codes PSoH = Pressure switch open with high pump. PSoL = Pressure switch open with low pump.

All rights reserved.

Other Heating Modes are Standard, Standard in Economy, and Sleep Modes.Ecn or Ec is ON Solid (Not Flashing):The Current Water Temperature is "Unknown" (- - - or - -) while in DO NOT remove the protective covers from any electrical enclosure, or attempt to service any related electrical device, unless you are a qualified electrician or service professional. One sensor has detected 110º F. Balboa Spa Control Manual Back to Top SAL or SANITIZER LOW Message At the ORP Sensor, the "Sanitizer Level is Low" (SAL).With an ORP Sensor Installed in the System, the Sanitizer Level is Below 740

This video is a part of the Balboa technical series.For information on replacement systems, visit http://www.balboawatergroup.com/Retro...© Balboa Water Group. If there is Now a "CrC" or "CHKSUM FAIL" Error Message, contact your Dealer or Service Organization. Blocked Skimmer.4. http://sovidi.com/error-codes/bdd-error-codes.php PSoC = Pressure switch open with circulating pump.

Back to Top rtC or RTC FAILURE Message The "Real Time Clock" (rtC) Cannot be Read.At Power-Up, the System Board Real Time Clock could Not be Read. Back to Top CrC or CHKSUM FAIL Message "Cyclic Redundancy Code" (CrC) Checksum Error.A "Cyclic Redundancy Code" (CrC) is a type of checksum algorithm that takes a string of data bytes If there is Now an Error Message, select Message Other than CFEor CONFIG ERROR below or contact your Dealer or Service Organization.No Error Messages:The "CFE" or "CONFIG ERROR" Configuration Error Appears Loading...

With the the Pump ON, prior to Heater ON, the Sensors differ by more than 2°F (1.0°C), indicating one or both Sensors are several degrees off.