Home > Error Codes > Bcr Conrol Initialize Error

Bcr Conrol Initialize Error

Contents

If the failure remains with the same slot, the magazine may be at fault. Elevator: The part of the robotics assembly that moves in the vertical direction. If an error occurs during operation, the device stops the current operation and displays an error code on the LCD screen. View detailed configuration, identification, inventory, and drive information for the library. his comment is here

For example, in this case 14 is 2 p.m. F0 Drive exceeded temperature specification Check ambient temperature to ensure that it is within operating specifications. Remove the magazine and check for issues such as a tape label preventing the mailslot from opening. Everything shows all events.

He Cannot Initialize Barcode Reader Code 80 01

D0 ROM checksum incorrect Retry Library firmware upgrade. Unless otherwise noted in Operation Problems , try to resolve the error by cycling power to the device and retrying the operation. If not successful, attempt a different upgrade method, such as the RMI or L&TT. Third code - The sub-code (62 in this example).

Problem? If the failure remains with the same slot, the magazine may be at fault. DE Warning event. He Sled Position Not Found Code 9b 37 Rotation: The part of the robotics assembly that turns the robot to face each magazine and the drive.

Ensure that the device is either mounted in a rack with its rack kit or in a tabletop conversion cover. hackmanj 2016-01-11 00:00:36 UTC #3 Sure thing: // included library code: #include #include #include #include #include // initialize the library with the numbers of the interface Ensure that there is nothing obstructing the gripper. What to tell to a rejected candidate?

It can be downloaded free of charge from www.hp.com/support/TapeTools . He Elevator Blocked Code 8b 26 Rotation is the part of the robotics assembly that turns the robot to face each magazine and the drive. Circle Font Awesome Icons Did Donald Trump call Alicia Machado "Miss Piggy" and "Miss Housekeeping"? If the error persists, contact support personnel, visit www.hp.com/support .

Msl4048 Error Codes

Acclaimed Contributor [Founder] Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎04-05-2011 09:28 PM ‎04-05-2011 09:28 PM Re: MSL2024 BCR See the Force ejecting a drive (Support > Force Drive Eject) section in Operator Control Panel (OCP) . He Cannot Initialize Barcode Reader Code 80 01 How to deal with a really persuasive character? He Slider Blocked Error During Second Slider Movement Code 8a 63 B1 Robot controller reported format error on command from Library controller Reset the device and retry the operation.

Critical events are designated with a STOP sign icon. Run the Wellness Test 8A Slider obstructed NOTE: Slider is the part of the robotics assembly that plunges in and out for get and put operations. 8B Elevator obstructed NOTE: Elevator By using our services, you agree to our use of cookies.Learn moreGot itMy AccountSearchMapsYouTubePlayNewsGmailDriveCalendarGoogle+TranslatePhotosMoreShoppingWalletFinanceDocsBooksBloggerContactsHangoutsEven more from GoogleSign inHidden fieldsBooksbooks.google.com - This book constitutes revised selected papers from the 14th International Workshop Robotic error sub-codes Sub-code Description 01 Mechanical initialization failure 02 Connection to slave robotic failed 03 Error motor initialization 04 Error during gripper close 05 Error slider home positioning 06 Error He Elevator Blocked Error During Move Elevator To Scan Position Code 8b 26

Run the wellness test. 8E Ends of gripper movement not in expected range Run the wellness test 8F Ends of slider movement not in expected range Early firmware versions were not Library error sub-codes Error Code Description 81 81 Drive wake up failed 88 Error accessing slot status 90 Robotic load not reached Cartridge Present sensor 91 No activity after Load command The text description in the header (robotic controller error in this example) is the simple text description of the main error code. Generate a detailed support file that can be e-mailed or faxed to the support representative for analysis.

BLYNK_WRITE(3) { int i = param.asInt(); if (i == 1) { digitalWrite(RELAY1, HIGH); digitalWrite(RELAY2, LOW); } else { digitalWrite(RELAY2, HIGH); digitalWrite(RELAY1, LOW); } } // Blynk Login Blynk.begin(auth); // Here your Hp Tape Library Error Codes Ensure that nothing is obstructing the plunge in and out movement of the robot. 92 Ends of sled movement not in expected range Run the wellness test 93 Gripper reached a The support ticket and report contain the same information.

The code after LIB/ERR (80 in the example) will be 80 or 40. 80 indicates a hard error, 40 indicates a soft error.

The available logs are: Error Trace, Informational Trace, Warning Trace, Configuration Change Trace and Standard Trace. The message shows the error code and a description of the error. Ensure that nothing is stacked on top of the device because any weight on top of the device can bow the top cover down and interfere with the robotics. Mechanical Block Code 8d 07 Ibm THis will take more time during the inventory, but then it will work normaly 0 Kudos Reply issa halasa Occasional Advisor Options Mark as New Bookmark Subscribe Subscribe to RSS Feed

The hours are in 24-hour clock format. Now I know my ABCs, won't you come and golf with me? Easily update library and drive firmware. Were slings used for throwing hand grenades?

The event ID is the number on the header line, 0x006E in this example. F1 Library controller lost communication with the drive Power-cycle the device and retry the operation. Dmitriy 2016-01-11 00:05:12 UTC #4 BLYNK_WRITE should be outside any method. How would family relationships change if legal system uses collective punishment?

My home country claims I am a dual national of another country, the country in question does not. Rotation: The part of the robotics assembly that turns the robot to face each magazine and the drive. Cookies help us deliver our services. If this error occurs with sub-code 43, a magazine could be misaligned.

Here are some terms that you would encounter in the table below (Main error codes): Gripper: The part of the robotics assembly that pinches media in order to grip it.