Home > Error Codes > Bcr Control Initialize Error

Bcr Control Initialize Error

Contents

Remove and inspect the magazine or drive for a stuck tape Run the Wellness Test B5 Robotic controller not responding to command from library controller Reset the unit Retry the operation Sled: The part of the robotics assembly that moves the robot towards the OCP or back towards the drive. DB External cooling fan error. If this error was caused by a manual magazine removal, replace the magazine and try the operation again. his comment is here

The wellness test exercises all robotic movements and checks the status of the electrical components and communication. Elevator is the part of the robotics assembly that moves in the vertical direction. Power down the Library and re-seat the library controller from the back panel. Slider is the part of the robotics assembly that plunges in and out for get and put operations.

He Cannot Initialize Barcode Reader Code 80 01

Was the information on this page helpful? See the Force ejecting a drive (Support > Force Drive Eject) section in Operator Control Panel (OCP) . The main error code (0x83) is displayed in parenthesis as the Global error code.

The text description in the header (robotic controller error in this example) is the simple text description of the main error code. If there is a tape in the robot, replace the magazines and power-cycle the device. If the device continues to fail, contact HP support. He Sled Position Not Found Code 9b 37 Check that the network configuration is correct.

is 13:00. Msl4048 Error Codes top Provide feedback Please rate the information on this page to help us improve our content. Check that the network configuration is correct. View detailed configuration, identification, inventory, and drive information for the library.

Thank you! He Elevator Blocked Code 8b 26 Discard the tape cartridge if it is damaged. Sled: The part of the robotics assembly that moves the robot towards the OCP or back towards the drive. hackmanj 2016-01-11 00:00:36 UTC #3 Sure thing: // included library code: #include #include #include #include #include // initialize the library with the numbers of the interface

Msl4048 Error Codes

Your cache administrator is webmaster. top Link for service and repair Click here to view information on Service and Repair . He Cannot Initialize Barcode Reader Code 80 01 The date is in the format year/month/day. He Elevator Blocked Error During Move Elevator To Scan Position Code 8b 26 Either void setup() { ... } either void setup() { ... } hackmanj 2016-01-11 00:07:19 UTC #6 You make it look easy, thanks very much, I moved it between setup and

If the device was moved, verify that each of the tape cartridges is properly seated in a magazine. 8A Slider obstructed Run the wellness test. The device must be supported under both of its side edges or the bottom can bow and impede robotic movement. Thank you! The format for the log entries is: YY.MM.DD HH.MM.SS.ss LIB/ERR<80 89 62 40 YY.MM.DD - The date displayed as Year.Month.Day HH.MM.SS.ss - The time displayed as Hour.Minute.Second.Hundredths fo a second First He Slider Blocked Error During Second Slider Movement Code 8a 63

For example, in this case 14 is 2 p.m. Explanation of error codes Example: On the Operator Control Panel (OCP), the code will be displayed as: Robotic Failure, Code: 9B 37. The hours are in 24-hour clock format. B1 Robot controller reported format error on command from Library controller Reset the device and retry the operation.

The support ticket and report contain the same information. Msl2024 Error Codes There are three ways to obtain error codes from the device: On the OCP On the RMI On an L&TT support ticket or report top Finding error code information on the Very helpful Somewhat helpful Not helpful End of content United StatesHewlett Packard Enterprise International Start of Country Selector content Select Your Country/Region and Language Click or use the tab key to

If this error occurs with sub-code 43, a magazine could be misaligned.

void setup() { ... } // Managing "Modes" For Xbox, etc. Critical events are designated with a STOP sign icon. F4 Time allotted for drive loading exceeded Check that the tape cartridge is supported and has not exceeded its usage life. Mechanical Block Code 8d 07 Ibm Clean the drive.

The code 9B is the main error code, 43 is the error sub-code, and 15 is sub-code specific information for factory use only. Run the wellness test. 8E Ends of gripper movement not in expected range Run the wellness test 8F Ends of slider movement not in expected range Early firmware versions were not Everything shows all events. For example, 1:00 pm is 13:00.D7 is the main error code50 is the error sub-code top Finding error code information on the RMI You can find error codes on the RMI

top Main error code descriptions The table below (Main error codes) lists the main error codes with details and a solution. D7 = main error code 50 = error sub-code Also see, Viewing logs (Support > View Logs) RMI error log On the RMI error log, an error entry is displayed as: Slider: The part of the robotics assembly that plunges in and out for get and put operations. To run the wellness test from the OCP, see the Running tests (Support > Run Tests) section in Operator Control Panel (OCP) .

The sub-code indicates the affected fan. sub-code 00: drive sled #1, sub-code 01: drive sled #2 NOTE: Sled is the part of the robotics assembly that moves the robot towards the OCP or back towards the drive. C2 Web server initialization failed C6 Ping command did not reach target C7 Cannot upgrade firmware from USB Retry the firmware upgrade. Dmitriy 2016-01-11 00:05:12 UTC #4 BLYNK_WRITE should be outside any method.

Ensure that nothing is obstructing the opening of the mailslot. To view a downloaded support ticket, perform the following steps: From the L&TT File menu, select Load Support Ticket. Library error sub-codes The following table lists the library error sub-codes. top Provide feedback Please rate the information on this page to help us improve our content.

Here are some terms that you would encounter in the table below (Main error codes): Gripper: The part of the robotics assembly that pinches media in order to grip it. while (Blynk.connect() == false) { // Wait until connected } // This will print Blynk Software version to the Terminal Widget when // will log messages here, test code functional terminal.println(F("Blynk Was the information on this page helpful? F2 Drive sled not present F3 Drive hardware error Cycle power, after several occurrences.

If the error persists, contact the support personnel. C1 Telnet interface initialization failed Check the network cable. DD Warning event. Slider: The part of the robotics assembly that plunges in and out for get and put operations.

B5 Robotic controller not responding to command from Library controller Reset the device and retry the operation. For example: 24/06/05 01:48 D7 50 System Error where: 24/06/05 = date in the format DD-MM-YY 01:48 = hours in 24h clock format. Generated Sat, 01 Oct 2016 22:31:53 GMT by s_hv972 (squid/3.5.20) Lichtsignaal 2016-01-11 05:29:43 UTC #8 You need to put it outside anything.